230.703 results (0,50305 seconds)

Show all filters

Brand

Show all

Colour

Show all

Size

Show all

Gender

Merchant

Show all

Price (EUR)

Show all

Reset filter

Products
From
Shops

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125DThe BV125D Amplifier module contains two independent Class D Power amplifiers each with a single 500mV Balanced Line audio input and 125-Watt 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level for both amplifiers.The audio inputs to each amplifier are presented on separate RJ45 connectors. The outputs are presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC inputs are presented on two 2-way crimp connected sockets. The power output stages of the amplifiers are protected against overload conditions i.e. short circuits or abnormal loads.Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.

GBP 1349.92
1

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225The BV225 Amplifier module is a 225-Watt Class D Power amplifier with a 500mV Balance Line audio input and 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level. The audio input is presented on two separate RJ45 connectors. The output is presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC input is presented on a two 2-way crimp connected socket.The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads. Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.Over temperature protection is provided using sensors attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to the relevant amplifier will be attenuated to a safe level and the Overload LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction.

GBP 870.91
1

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11Power amplifier for the voice alarm system VARIODYN D1 in class D technologies with four independent power channels and galvanic isolated 100 V direct outputs symmetric inputs inrush current limitation and soft start. In comparison to our 4XDxxxB series amplifiers one amplifier can back up another amplifier. Four built-in fans with smooth temperature controlled speed control.Key FeaturesBuilt- in electronic protective circuit against thermal overload DC signals sub frequent signals short circuit open outputs and HF interferenceIndividual status LEDs indicate channel CLIP PROTECT SIGNAL POWER LINE and 24 V DC power Back switch contact for sequential remote power2 back fault message contactsBack fault message contact for missing 24 V emergency power supply24 V emergency power supply inputSuitable for use with loop technology

GBP 8099.83
1

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11Power amplifier for the voice alarm system VARIODYN D1 in class D technologies with four independent power channels and galvanic isolated 100 V direct outputs symmetric inputs inrush current limitation and soft start. In comparison to our 4XDxxxB series amplifiers one amplifier can back up another amplifier. Four built-in fans with smooth temperature controlled speed control.Key FeaturesBuilt- in electronic protective circuit against thermal overload DC signals sub frequent signals short circuit open outputs and HF interferenceIndividual status LEDs indicate channel CLIP PROTECT SIGNAL POWER LINE and 24 V DC power Back switch contact for sequential remote power2 back fault message contactsBack fault message contact for missing 24 V emergency power supply24 V emergency power supply inputSuitable for use with loop technology

GBP 4644.12
1

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242Four-channel power amplifier with built in battery charger for emergency power supply of VARIODYN D1 Comprio. 4XD125B has 4 independent amplifier channels each with 125 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB models. The amplifier may be used with the VARIODYN D1 Comprio as well as a DOM. It is also possible to use the amplifier with a separate PSU in this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelOne height unitIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 65 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 3463.82
1

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050QThe Vigil2 BV050Q contains four independent 50 Watt Class D Power amplifiers each with one 500 mV balanced input and a 50 Watt 100V Line output. The front panel status indicators show Supply Healthy Overload Over Temperature and Output Level 10 and 100 max output level for each amplifier. The Active Indicator illuminates when the amplifier is not in Sleep Mode. CLASS D amplifiers are 80 efficient therefore reducing unwanted heat dissipation and power input requirements. Rated output power is obtainable using a 22V battery supply.The BV050Q has a Sleep mode automatically reducing the standby current requirement to typically 50mA per amplifier when operating on batteries. Channel gain may be individually set using the potentiometers on the board behind the front panel. The audio inputs to the amplifiers are presented on separate RJ45 connectors each connector providing the balanced audio input and a ground connection. The outputs are presented on 6-way plugscrew termination connectors providing 50V or 100V output. The 24V DC input is presented on a 2-way crimp connected plug and socket. The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads etc. Should the amplifier be subjected to an abnormal load the input to the power amplifier is attenuated to a safe level.The amplifiers output voltage is also sensed and should it exceed 100V the input signal will be attenuated ensuring safe operation without creating unnecessary distortion. Over temperature protection is provided using a sensor attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to will be attenuated to a safe level and the Overtemp LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction. Up to three BV050Q Amplifier modules may be mounted in one BVMF equipment frame or more normally two amplifier modules and one switched mode power supply charger module.

GBP 1973.16
1

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243Four-channel amplifier with integrated battery recharging system for the emergency power supply to the VARIODYN D1 Comprio. The 4XD250B features 4 independent amplifier channels each with 250 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB and 4XDxxxW models. The amplifier can be used in combination with the VARIODYN D1 Comprio as well as with a DOM. It is also possible to use the amplifier also with a separate PSU the internal PSU must be switched of then. In this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelTwo Height Unit 2 HUIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 105 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 5451.26
1

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150Q

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150Q

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150QThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV150Q Quad 150W transformerless class D amplifier. Contains four independent 150W each amplifier has a single balanced line audio input and 150W 100V line output. Can either be used as four independent amplifier modules or four amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2944.78
1

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075D

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075D

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV075D Dual 75W transformerless class D amplifier. Contains two independent 75W each amplifier has a single balanced line audio input and 75W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 1532.26
1

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300D

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300D

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV300D Dual 300W transformerless class D amplifier. Contains two independent 300W each amplifier has a single balanced line audio input and 300W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2413.15
1

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075Q

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075Q

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075QThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV075Q Quad 75W transformerless class D amplifier. Contains four independent 75W each amplifier has a single balanced line audio input and 75W 100V line output. Can either be used as four independent amplifier modules or four amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2509.32
1

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150D

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150D

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV150D Contains two independent 150W each amplifier has a single balanced line audio input and 150W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 1787.18
1

Kidde Airsense EST-PA1650B Power Amplifier D-Class 1x650 Watt

Kidde Airsense EST-PA1650B Power Amplifier D-Class 1x650 Watt

Kidde Airsense EST-PA1650B Power Amplifier D-Class 1x650 WattThe Amplifiers are designed for perfect integration into the EST solutions. Thanks to their flexibility they can also be used for any other Public Address and Voice Evacuation applications. These amplifiers have been developed to meet the specific requirements of the EN 54-16 standard for safety installations.The EST-PAXXXXB is a family of 2U rack mountable 8-channel ESTPA8080B ESTPA-8160B 4 channel EST-PA4160B 2 channel high power EST-PA2650B and 1 channel EST-PA1650B class-D transformer isolated power amplifiers for 50 V and 100 V distributed loudspeaker systems. Amplifier EST-PA8080B can deliver up to 8 x 80 W for EST-PA8160B and EST-PA2650B delivering power increases respectively to the 8 x 160 W and 2 x 650 W. In a bridged mode amplifier channels are combined and can deliver 4 x 160 W for ESTPA8080B 4 x 320 W for EST-PA8160B and 1 x 1300 W for ESTPA2650B. These amplifiers have 48 VDC input which allows to connect with battery backup system for maximum availability and durability in a voice evacuation system.The EST-PAXXXXB amplifiers are powered from external power supply module EST-PS48800 working in a block. The current from block is distributed to individual amplifiers through the power manager EST-PSM48 device includes a battery charger and is in compliance with EN 54-4.Key FeaturesFront panel indicators include Supply Active Fault100 50 Volt available via terminal blocks at the rearEST-PAXXXXB combines with the EST-PSM48 Power Supply Manager charger and back-up supply

GBP 1102.58
1

Gent 585031 4 Channel 250W Class D Amplifier With Battery Charger

Gent 585031 4 Channel 250W Class D Amplifier With Battery Charger

Gent 585031 4 Channel 2050W Class D Amplifier With Battery ChargerThe UIM serves as the interface module of the VARIODYN ONE PAVA system for connecting two analog audio inputs two analog audio outputs as well as 48 control contacts.For eight control contacts short-circuit and interruption monitoring can be activated. The UIM is connected to the VARIODYN ONE module INC via the DAL bus. It digitizes two analog audio inputs i.e. from a CD player or a hazard detection system and transmits the digitized audio data to the VARIODYN ONE module INC via the DAL bus. In order to transmit all played messages to an external device for instance two outputs are available as analog audio sources. The 48 contacts can serve as contact inputs or as contact inputs. For eight control contacts short-circuit and interruption monitoring can be activated.Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up. This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power.Key Features48 programmable Inputs Outputs8 monitored contacts2 Audio Inputs2 Audio OutputsConnected to INC via DAL Digital Audio Link portCan connect up to 8 UIMs per INC- D controller

GBP 4394.12
1

Gent 585034 4 Channel 2000W Class D Amplifier With Power Sharing

Gent 585034 4 Channel 2000W Class D Amplifier With Power Sharing

Gent 585034 4 Channel 2000W Class D Amplifier With Power SharingThe UIM serves as the interface module of the VARIODYN ONE PAVA system for connecting two analog audio inputs two analog audio outputs as well as 48 control contacts.For eight control contacts short-circuit and interruption monitoring can be activated. The UIM is connected to the VARIODYN ONE module INC via the DAL bus. It digitizes two analog audio inputs i.e. from a CD player or a hazard detection system and transmits the digitized audio data to the VARIODYN ONE module INC via the DAL bus. In order to transmit all played messages to an external device for instance two outputs are available as analog audio sources. The 48 contacts can serve as contact inputs or as contact inputs. For eight control contacts short-circuit and interruption monitoring can be activated.Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up. This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power.Key Features48 programmable Inputs Outputs8 monitored contacts2 Audio Inputs2 Audio OutputsConnected to INC via DAL Digital Audio Link portCan connect up to 8 UIMs per INC- D controller

GBP 5387.87
1

Gent 585030 4 Channel 125W Class D Amplifier With Battery Charger

Gent 585030 4 Channel 125W Class D Amplifier With Battery Charger

Gent 585030 4 Channel 125W Class D Amplifier With Battery ChargerThe UIM serves as the interface module of the VARIODYN ONE PAVA system for connecting two analog audio inputs two analog audio outputs as well as 48 control contacts.For eight control contacts short-circuit and interruption monitoring can be activated. The UIM is connected to the VARIODYN ONE module INC via the DAL bus. It digitizes two analog audio inputs i.e. from a CD player or a hazard detection system and transmits the digitized audio data to the VARIODYN ONE module INC via the DAL bus. In order to transmit all played messages to an external device for instance two outputs are available as analog audio sources. The 48 contacts can serve as contact inputs or as contact inputs. For eight control contacts short-circuit and interruption monitoring can be activated.Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up. This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power.Key Features48 programmable Inputs Outputs8 monitored contacts2 Audio Inputs2 Audio OutputsConnected to INC via DAL Digital Audio Link portCan connect up to 8 UIMs per INC- D controller

GBP 2998.42
1