tapis de billard from GBP 551 | See the cheapest prices and offers on Cobiro CSS.com

Klaxon SWG-0034 FP10 ATEX Motor Siren - 400VAC - 50Hz

Klaxon SWG-0034 FP10 ATEX Motor Siren - 400VAC - 50HzThe FP10 is a flameproof version of Klaxons wide area siren providing effective signalling over large distances and mass alert signalling in hazardous area locations for all industrial civil commercial and environmental requirements.Utilising a traditional siren sound it provides a recognisable alarm and is often used for critical alarms such as toxic gas release and disaster warning.Certified to EExd llC T4 the FP10 is manufactured from cast aluminium and will give a very long life when mounted outdoors. Powered by a 3 phase motor it is designed for roof or pole mounting.Using appropriate control equipment the siren can produce two distinct tones for different types of alarm.Key FeaturesAudibility range between 135db 1 metre475Hz constant tone signalATEX approved for zone 1 2Overall siren standard approval Exd IIG IIC T4Non electrical parts standard approval EExc IIC T1 T6 XRoughly omni-directional sound coverage which peaks in the direction of the front stator face400Vac - 10 50Hz 3 phase nominal power supply requirementOperating temperature range for the FP6 FP10 units of -20 to 60 degrees CCast aluminium steel constructionEnvironmental rating of IP55If the power supply to the sirens is pulsed to enable the siren to produce a wail tone then the maximum run time of the siren is reduced from continuous for constant tone to 15 minutes or lessControl units can be supplied to enable the siren to produce the wail tone signal with associated control switches. The controls are only suitable for locating in a non-hazardous areaThe Motor windings are tropicalized as standardAnti-condensation heaters for the motor can be suppliedThe standard siren builds offered are fitted with EExde rated motorsMotor power 7.5Kw de-rated to 5.5Kw for 60C operationCurrent rating 11AWeight 143KgDimensions 612 x 495 x 557mm

GBP 8448.63

1

Patol 710-020 Controller 5020 for Spares Only

Patol 710-020 Controller 5020 for Spares Only - for use with Sensor Models 5010 5012 5712The 5020 controller is directly connected to the sensor. A series of user programmable DIL switches allows option selection including detector sensitivity settings automanual reset sequence selection and single coincidence voting from the four individual internal detection channels for the alarm trip and shutdown outputs.The Sensor Unit is located above the materials transit path e.g. conveyor by means of the adjustable mounting bracket and aligned such that the monitored hazard passes through the sensors field of view. The height and angle of the sensor determine the width of the monitored path.The Type 5020 Control Unit provides various indications and controls related to infra-red detection alarms and fault monitoring.The control module is easily de-mountable from the housing and connects to the sensor by means of a ten core screened shielded cable. These terminations together with supply and output contact connections are via two part screw terminals thus enabling installation of the housing and site cables prior to fitment of the module. The housing has a high level of ingress protection IP67.The unit incorporates a user programmable DIL switch to set the options which include detector sensitivity setting automanual reset sequence selection and one-shot coincidence voting for the alarm and tripshutdown outputs.The sensor air pressure and signal cable connections are fault monitoredfail safe. The unit incorporates an aux. fault input common fault output contact.The 5020 Controller also includes LED indication of the four detector channels along with LED indication and relay outputs for Alarm Trip and Fault.The controller can be provided in an optional outer control panel together with power supplies battery chargers DIN rail terminals as required.Key FeaturesMaterial Fan Case - White Polyester Resin Impellors - Aluminium 1200 H14IP Rating IP44Weight 8.5Kg

GBP 1664.57

1

Fireclass DB3B Flameproof Horn Sounder - High Power

Fireclass DB3BDGD048N2BNRFC DB3B Flameproof Horn Sounder High Power Explosion Proof 122dB 1mThe DB3B is a high-power explosion proof sounder introduced as a replacement for the current DB3 with improved functionality and performance.Certified for use in a wide range of temperatures from -55C to 70C the Ex enclosure is manufactured from GRP with a rugged thermoplastic flare providing a corrosion free and aesthetically pleasing product.Capable of producing 122dB 1m and with a range of pre-recorded tones the DB3B includes an integral volume control which is ideal when a lower output is required.The unit is provided with versatile control options allowing compatibility with a wide range of control methods and PLCs.The standard DC unit provides 3 tone stages each stage has 28 tones available which can be independently selected. The unit can be controlled by reversing the polarity of the power supply 2 stage or providing a common negative and switching between multiple positive supplies. The DB3B proves its versatility by additionally being able to work with a common positive supply and switching the negatives. The tone stages of the DB3B can also be controlled via voltage free contacts provided by a control panel.Key FeaturesEx d Ex de IICIIIC T4T5T6ATEX certifiedIECEx certifiedUL certified for USA and Canada Class I Div 2 Groups A-D Class I Zone 1 Ex d IICAEx d IIC Gb Class II Div 2 Groups F G Zone 21 AEx tb IIIC Class III Div. 1TR CU certifiedCQST certifiedCCOE certifiedChinese Compulsory Certification for Fire systems CCCF certifiedINMETRO certifiedSIL 1 certifiedCSFM certifiedUp to 122dB output 1mIntegral volume control28 tones user selectable3 stage unit remotely switchableTones can be programmed to customers specificationDC supply voltage between 12V and 48VEx enclosure - glass reinforced polyesterFlare - high impact thermoplastic polyester

GBP 592.05

1

Scope TLINKAC Telemetry System for One-way Link DL3-05-AC amp RX10SAC

Scope TLINKAC Telemetry System for One-way Link DL3-05-AC RX10SACT-Link takes a 5-zone DigiLink transmitter and combines it with a RX10 receiver and two aerials to produce an off the shelf one-way radio link between fire or intruder panels. The transmitter has five input zones which can be triggered by volts-free opening or closing contacts or can be configured to accept voltage applied or voltage removed.The system is supplied pre-configured to operate change-of-state so a closing contact at the transmitter sends a signal to the receiver to activate the corresponding zone output relay. When the transmitter input is de-activated the relay is deactivated so the output actually follows the input. A programming kit is available if you need to reconfigure the system. Additional transmitters and receivers can be added when needed.This can simply be achieved by installing Digilink transmitters and receivers adjacent to the fire or security panels where their relay contacts can be hard wired into the output inputs of the panel in order to provide wireless alarm signals between buildings. For roaming fire marshals and security personnel the serial output of the receiver can be connected to the Scope Connexions Range of paging transmitters in order to send pre-programmed text messages to pocket worn pagers.It is also possible to connect the printer output of analogue addressable panel to a serial port of the Connexions transmitter in order to transmit real time panel messages to the pagers thus saving valuable time by not having to view the message at the panel. The same format could also be deployed for access control plant monitoring lone worker and care home applications where staff has to be made aware of situations arising from automated or manual inputs.

GBP 862.99

1

Scope TLINK12V Telemetry System for One-way Link DL3-05-12V amp RX10SDC

Scope TLINK12V Telemetry System for One-way Link DL3-05-12V RX10SDCT-Link takes a 5-zone DigiLink transmitter and combines it with a RX10 receiver and two aerials to produce an off the shelf one-way radio link between fire or intruder panels. The transmitter has five input zones which can be triggered by volts-free opening or closing contacts or can be configured to accept voltage applied or voltage removed.The system is supplied pre-configured to operate change-of-state so a closing contact at the transmitter sends a signal to the receiver to activate the corresponding zone output relay. When the transmitter input is de-activated the relay is deactivated so the output actually follows the input. A programming kit is available if you need to reconfigure the system. Additional transmitters and receivers can be added when needed.This can simply be achieved by installing Digilink transmitters and receivers adjacent to the fire or security panels where their relay contacts can be hard wired into the output inputs of the panel in order to provide wireless alarm signals between buildings. For roaming fire marshals and security personnel the serial output of the receiver can be connected to the Scope Connexions Range of paging transmitters in order to send pre-programmed text messages to pocket worn pagers.It is also possible to connect the printer output of analogue addressable panel to a serial port of the Connexions transmitter in order to transmit real time panel messages to the pagers thus saving valuable time by not having to view the message at the panel. The same format could also be deployed for access control plant monitoring lone worker and care home applications where staff has to be made aware of situations arising from automated or manual inputs.

GBP 637.26

1

Scope TLINKLT Telemetry System for One-way Link DL3-05-12V amp RX10LT

Scope TLINKLT Telemetry System for One-way Link DL3-05-12V RX10LTT-Link takes a 5-zone DigiLink transmitter and combines it with a RX10 receiver and two aerials to produce an off the shelf one-way radio link between fire or intruder panels. The transmitter has five input zones which can be triggered by volts-free opening or closing contacts or can be configured to accept voltage applied or voltage removed.The system is supplied pre-configured to operate change-of-state so a closing contact at the transmitter sends a signal to the receiver to activate the corresponding zone output relay. When the transmitter input is de-activated the relay is deactivated so the output actually follows the input. A programming kit is available if you need to reconfigure the system. Additional transmitters and receivers can be added when needed.This can simply be achieved by installing Digilink transmitters and receivers adjacent to the fire or security panels where their relay contacts can be hard wired into the output inputs of the panel in order to provide wireless alarm signals between buildings. For roaming fire marshals and security personnel the serial output of the receiver can be connected to the Scope Connexions Range of paging transmitters in order to send pre-programmed text messages to pocket worn pagers.It is also possible to connect the printer output of analogue addressable panel to a serial port of the Connexions transmitter in order to transmit real time panel messages to the pagers thus saving valuable time by not having to view the message at the panel. The same format could also be deployed for access control plant monitoring lone worker and care home applications where staff has to be made aware of situations arising from automated or manual inputs.

GBP 550.68

1

Brand