21 results (0,12531 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

CCMT 09T302 Insert Grade IC20N

CCMT 09T302 Insert Grade IC20N

These turning inserts are single-sided, 7 positive relief angle inserts that are ideal for semi-finish and finish cutting. They have an "M" tolerance edge condition, meaning they are suitable for general applications. The inserts have numerous benefits, including chip breaking in moderate feed range, positive rake and low cutting forces. Used for a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits Wear resistant Suitable for general applications Positive rake and low cutting force Typical Applications Turning Grooving Semi-finishing Finishing

GBP 5.99
1

GFN-2 Insert Grade IC328

GFN-2 Insert Grade IC328

A thin PVD coated layer on a tough substrate,for milling, parting and grooving mainly steel and stainless steel at low to medium cutting speeds especially in unstable machining conditions. Features and Benefits Tough substrate for greater strength and hardness Thin PVD TiCN coated layer for greater heat and wear resistance Designed to operate at low to medium cutting speeds and in unstable machining conditions Typical Applications Parting Milling Grooving Steel Stainless steel

GBP 8.39
1

CNMG 120404-TF Insert Grade IC907

CNMG 120404-TF Insert Grade IC907

CNMG Turning Inserts grade IC907 designed for machining of heat resistant alloys, austenitic stainless steel and hard steel. Features and Benefits Double-sided negative (0) relief angle inserts offering a strong edge for general applications and varying depths of cut dependent on chipbreaker type A tough sub-micron substrate, suitable for low-to-medium cutting speeds Rake angle which is positive and varies along the edge to negative in order to prevent chipping Specially designed reduces cratering

GBP 8.39
1

CNMG 120412-TF Insert Grade IC907

CNMG 120412-TF Insert Grade IC907

CNMG Turning Inserts grade IC907 designed for machining of heat resistant alloys, austenitic stainless steel and hard steel. Features and Benefits Double-sided negative (0) relief angle inserts offering a strong edge for general applications and varying depths of cut dependent on chipbreaker type A tough sub-micron substrate, suitable for low-to-medium cutting speeds Rake angle which is positive and varies along the edge to negative in order to prevent chipping Specially designed reduces cratering

GBP 8.39
1

TNMG 160404-TF Insert Grade IC907

TNMG 160404-TF Insert Grade IC907

TNMG TF Turning Inserts Grade IC90 feature a tough sub-micron substrate, suitable for low-to-medium cutting speeds. For machining of heat resistant alloys, austenitic stainless steel and hard steel. Features and Benefits Tough submicron substrate for added hardness PVD TiAlN+TiN coating for enhanced heat and wear resistance TF chipbreaker for use at slow to medium cutting speeds Standards Insert Grade IC907 ISO Range - (P10-P30)(M05-M20)(K15-K30)(H05-H15)(S05-S20)(N05-N20)

GBP 6.99
1

TNMG 160408-TF Insert Grade IC907

TNMG 160408-TF Insert Grade IC907

TNMG TF Turning Inserts Grade IC90 feature a tough sub-micron substrate, suitable for low-to-medium cutting speeds. For machining of heat resistant alloys, austenitic stainless steel and hard steel. Features and Benefits Tough submicron substrate for added hardness PVD TiAlN+TiN coating for enhanced heat and wear resistance TF chipbreaker for use at slow to medium cutting speeds Standards Insert Grade IC907 ISO Range - (P10-P30)(M05-M20)(K15-K30)(H05-H15)(S05-S20)(N05-N20)

GBP 7.29
1

CCMT 060204-SM Insert Grade IC9250

CCMT 060204-SM Insert Grade IC9250

CCMT turning inserts single-sided, 7 positive relief angle inserts for semi-finish and finish cutting. "M" tolerance edge condition for general applications. Chip breaking in moderate feed range. Positive rake, low cutting forces. Used for a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits Tough substrate with a cobalt enriched layer for greater cutting strength Thick CVD TiCN+alpha Al2O3+TiN coating for high toughness and wear resistance Chipbreaker SM for finishing applications Typical Applications General use machining Steel Standards Insert Grade IC9250 ISO Range - (P10-P35)(M05-M20)

GBP 5.99
1

CCMT 09T308-SM Insert Grade IC9250

CCMT 09T308-SM Insert Grade IC9250

CCMT turning inserts single-sided, 7 positive relief angle inserts for semi-finish and finish cutting. "M" tolerance edge condition for general applications. Chip breaking in moderate feed range. Positive rake, low cutting forces. Used for a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits Tough substrate with a cobalt enriched layer for greater cutting strength Thick CVD TiCN+alpha Al2O3+TiN coating for high toughness and wear resistance Chipbreaker SM for finishing applications Typical Applications General use machining Steel Standards Insert Grade IC9250 ISO Range - (P10-P35)(M05-M20)

GBP 6.99
1

CCMT 09T304-SM Insert Grade IC9250

CCMT 09T304-SM Insert Grade IC9250

CCMT turning inserts single-sided, 7 positive relief angle inserts for semi-finish and finish cutting. "M" tolerance edge condition for general applications. Chip breaking in moderate feed range. Positive rake, low cutting forces. Used for a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits Tough substrate with a cobalt enriched layer for greater cutting strength Thick CVD TiCN+alpha Al2O3+TiN coating for high toughness and wear resistance Chipbreaker SM for finishing applications Typical Applications General use machining Steel Standards Insert Grade IC9250 ISO Range - (P10-P35)(M05-M20)

GBP 7.29
1

WBMT 060102L Insert Grade IC530N

WBMT 060102L Insert Grade IC530N

WBMT turning inserts 80 trigon insert 5 positive flank inserts with a ground chipformer. Used for for finishing on miniature boring bars, provide excellent surface finish. Suitable for a wide range of materials. Features and Benefits Cermet construction for rigidity and stability TiCN & TiN PVD coated for increased wear resistance Used in high speed semi-finishing and finishing applications with excellent surface finish Specifications Grade : IC530N ISO Range - (P10-P30)(M10-M20) Grade or Coating Type: PVD Coating Layers: TiCN+TiN Cermet construction TiCN & TiN PVD coated Typical Applications Turning Finishing

GBP 8.49
1

CCMT 060202-SM Insert Grade IC9250

CCMT 060202-SM Insert Grade IC9250

CCMT turning inserts single-sided, 7 positive relief angle inserts for semi-finish and finish cutting. "M" tolerance edge condition for general applications. Chip breaking in moderate feed range. Positive rake, low cutting forces. Used for a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits Tough substrate with a cobalt enriched layer for greater cutting strength Thick CVD TiCN+alpha Al2O3+TiN coating for high toughness and wear resistance Chipbreaker SM for finishing applications Typical Applications General use machining Steel Standards Insert Grade IC9250 ISO Range - (P10-P35)(M05-M20)

GBP 6.29
1

CCMT 09T304-SM Insert Grade IC907

CCMT 09T304-SM Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 6.99
1

CCMT 09T304-PF Insert Grade IC907

CCMT 09T304-PF Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 6.99
1

CCMT 060204-PF Insert Grade IC907

CCMT 060204-PF Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 5.99
1

CCMT 060202-PF Insert Grade IC907

CCMT 060202-PF Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 5.99
1

DCMT 11T302-SM Insert Grade IC530N

DCMT 11T302-SM Insert Grade IC530N

DCMT 55 rhombic turning inserts feature a 7 positive flank inserts used for semi-finishing and finish turning. Chip breaking in moderate feed range with a positive rake, low cutting forces and ideal for a wide range of materials. Features and Benefits A cermet grade, TiCN & TiN PVD coated for added durability Ideal for high speed semi-finishing and finishing applications Provides an excellent surface finish Wear resistant preventing built up edge Specifications Insert Grade IC530N ISO Range - (P10-P30)(M10-M20) Grade or Coating Type: PVD Coating Layers: TiCN+TiN Typical Applications Finishing Semi-finishing

GBP 7.59
1

GFN-5 Insert Grade IC354

GFN-5 Insert Grade IC354

GFN SELF-GRIP parting and grooving inserts are self locking making them ideal for parting and grooving applications. Featuring a positive rake, single cavity and negative land and shoulders they provide extra cutting strength in medium to high feeds. Their PVD coating helps reduce their susceptibility to wear and heat. Features and Benefits Self locking for greater stability Positive rake and single cavity for greater chip flow Negative land and shoulders for greater strength PVD coating helps reduce wear and heat Standards IC354 (P20 - P40, M10 - M30) PVD coated Medium speed - high feed Typical Applications Parting Grooving Carbon steel Alloy steel Stainless steels

GBP 6.99
1

CCMT 09T304-14 Insert Grade IC907

CCMT 09T304-14 Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 6.99
1

TPMR 160308 Insert Grade IC907

TPMR 160308 Insert Grade IC907

TPMR turning inserts feature a tough sub-micron substrate, suitable for low-to-medium cutting speeds. For machining of heat resistant alloys, austenitic stainless steel and hard steel. The 11 positive relief angle is ideal for semi-finishing and finishing of most materials. Features and Benefits PVD TiAlN+TiN coating for excellent heat and wear resistance Tough sub-micron substrate for increased hardness Semi-finishing/ finishing geometry for finalisation of work pieces PF chipbreaker for improved chip flow and control Typical Applications Turning Heat resistant alloys Austenitic stainless steel Stainless steel Semi-finishing Finishing Standards Insert Grade IC907 ISO Range - (P10-P30)(M05-M20)(K15-K30)(H05-H15)(S05-S20)(N05-N20)

GBP 6.99
1

TPMR 160304 Insert Grade IC907

TPMR 160304 Insert Grade IC907

TPMR turning inserts feature a tough sub-micron substrate, suitable for low-to-medium cutting speeds. For machining of heat resistant alloys, austenitic stainless steel and hard steel. The 11 positive relief angle is ideal for semi-finishing and finishing of most materials. Features and Benefits PVD TiAlN+TiN coating for excellent heat and wear resistance Tough sub-micron substrate for increased hardness Semi-finishing/ finishing geometry for finalisation of work pieces PF chipbreaker for improved chip flow and control Typical Applications Turning Heat resistant alloys Austenitic stainless steel Stainless steel Semi-finishing Finishing Standards Insert Grade IC907 ISO Range - (P10-P30)(M05-M20)(K15-K30)(H05-H15)(S05-S20)(N05-N20)

GBP 6.99
1

TPMR 110304-PF Insert Grade IC907

TPMR 110304-PF Insert Grade IC907

TPMR turning inserts feature a tough sub-micron substrate, suitable for low-to-medium cutting speeds. For machining of heat resistant alloys, austenitic stainless steel and hard steel. The 11 positive relief angle is ideal for semi-finishing and finishing of most materials. Features and Benefits PVD TiAlN+TiN coating for excellent heat and wear resistance Tough sub-micron substrate for increased hardness Semi-finishing/ finishing geometry for finalisation of work pieces PF chipbreaker for improved chip flow and control Typical Applications Turning Heat resistant alloys Austenitic stainless steel Stainless steel Semi-finishing Finishing Standards Insert Grade IC907 ISO Range - (P10-P30)(M05-M20)(K15-K30)(H05-H15)(S05-S20)(N05-N20)

GBP 5.19
1