27 results (0,14275 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

PICCO R050.3-10 Insert Grade IC908

PICCO R050.3-10 Insert Grade IC908

This insert is designed for internal turning and chamfering. It is highly versatile, being able to handle numerous applications on a range of materials and at varying cutting speeds. The insert is also highly resistant to to wear and has excellent chipping durability. Features and Benefits Highly versatile insert Tough, with excellent resistances to wear and chipping Wide range of cutting speeds Typical Applications Steels Alloy steels Austenitic stainless steel High temperature alloys

GBP 37.99
1

GFR-1.6J-15D Insert Grade IC20

GFR-1.6J-15D Insert Grade IC20

Uncoated carbide inserts are designed for grey cast iron over 220HBN, malleable cast iron, silicon aluminum and copper alloys. They are suitable for finishing and medium finishing at medium speed, medium feed and interrupted cut conditions. The inserts have high wear resistance. They are grade IC20. Features and Benefits Built for grooving and parting a variety of materials High wear resistance Uncoated carbide Typical Applications Finishing and medium finishing Aluminium Brass Cast Iron Copper High-temperature alloys Stainless Steel Thermoplastic

GBP 25.99
1

Tag N2C Insert Grade IC83 0

Tag N2C Insert Grade IC83 0

A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Designed for machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds, interrupted cut and unfavourable conditions. Excellent notch wear and built-up edge resistance. Features and Benefits Tough submicron substrate for greater tool hardness Excellent notch wear and built-up edge resistance TiAIN PVD coated for better chip flow, heat and wear resistance Typical Applications Parting Grooving Steel Stainless steel

GBP 36.99
1

WNMG 060408-M3M Insert Grade IC806

WNMG 060408-M3M Insert Grade IC806

WNMG Turning Inserts are 80 trigon shaped double sided inserts with a negative 0 relief angle offering a strong edge for general applications and varying depths of cut (dependent on chipbreaker). Suitable for use on most materials. Features and Benefits Double sided cutting faces for increased versatility PVD AlTiN "SUMO TEC" coating for greater durability Manufactured from a tough submicron substrate for improved rigidity Specifications Insert Grade IC806 ISO Range - (S15-S25) Coating - PVD AlTiN "SUMO TEC" A tough submicron substrate Suitable for low to medium cutting speeds Typical Applications Turning Steel Cast iron

GBP 34.99
1

T490 LNMT 0804PNR-CS Insert Grade IC830

T490 LNMT 0804PNR-CS Insert Grade IC830

T490 LNMT HELITANG Milling Inserts are tangentially clamped inserts with 4 helical cutting edges. The unique pocket design prevents insert pull-out and enables tools with larger core diameters compared with regular radially orientated inserts. Features and Benefits Tangentially clamped with 4 helical cutting edges Unique pocket design prevents insert pull-out Enables tools with larger core diameters High toughness and wear resistance Specifications Insert grade: IC830 ISO range P/M/K: (P20-P40)(M25-M35) ISO range H/S/N: (S15-S30) Coating type: PVD Coating layers: AlTiN+TiN Typical Applications Steel Stainless steel High temperature applications

GBP 19.99
1

P290 Ackt 1806PDR-FW Insert GRADEIC810

P290 Ackt 1806PDR-FW Insert GRADEIC810

P290 ACCT are single-sided rectangular milling inserts with two 12 and 18 mm straight cutting edges with a 'SUMO TEC' AlTiN+TiN PVD coating. Recommended for interrupted cut and heavy operations on stainless steel, high temperature and alloyed steel. Features and Benefits 2 x cutting edges Durable 'SUMO TEC' AlTiN+TiN PVD coating for prolonged tool life High toughness and wear resistance Specifications Insert Grade IC830 ISO Range - P/M/K: (P20-P40)(M25-M35) ISO Range - H/S/N: (S15-S30) Grade or Coating Type: PVD Coating Layers: AlTiN+TiN Typical Applications Milling Steel Stainless steel Alloy steel High temperature applictions

GBP 21.99
1

DGN 3102C Insert Grade IC 354

DGN 3102C Insert Grade IC 354

DGN/DGNC/DGNM-C : Used for parting of bars, hard materials and tough applications. A positive rake, single cavity with a negative land and shoulders. Medium-to-high feeds. DGNC - with coolant holes, DGNM - single ended for very deep applications. Features and Benefits A thin PVD coated TiCN layer on a P40 substrate High toughness and durability For general applications in parting and grooving steel at medium to high speedsSpecifications Grade: IC354 ISO Range - P/M/K: (P20-P40)(M10-M30) Grade or Coating Type: PVD Coating Layers: TiCNTypical Applications Parting Grooving Steel Steel alloys Stainless streel

GBP 23.99
1

DGN 2002C Insert Grade IC 354

DGN 2002C Insert Grade IC 354

DGN/DGNC/DGNM-C : Used for parting of bars, hard materials and tough applications. A positive rake, single cavity with a negative land and shoulders. Medium-to-high feeds. DGNC - with coolant holes, DGNM - single ended for very deep applications. Features and Benefits A thin PVD coated TiCN layer on a P40 substrate High toughness and durability For general applications in parting and grooving steel at medium to high speedsSpecifications Grade: IC354 ISO Range - P/M/K: (P20-P40)(M10-M30) Grade or Coating Type: PVD Coating Layers: TiCNTypical Applications Parting Grooving Steel Steel alloys Stainless streel

GBP 23.99
1

H400 RNHU 1606-HP Insert Grade IC830

H400 RNHU 1606-HP Insert Grade IC830

H400 RNHU HP milling inserts are double-sided inserts with four 5, 6 and 8 mm Radii cutting edges for profile milling applications. Available are three different insert configurations for machining different materials and applications (HELIDO ROUND H400 LINE). Features and Benefits Durable 'SUMO TEC' AlTiN+TiN PVD coated grade for heavy operations Double sided for improved cutting performance High toughness and wear resistance Typical Applications Interrupted cut Heavy operations Stainless steel High temperature Alloyed steel Standards Insert Grade IC830 ISO Range - P/M/K: (P20-P40)(M25-M35) ISO Range - H/S/N: (S15-S30)

GBP 18.99
1

DGN 4003C Insert Grade IC 354

DGN 4003C Insert Grade IC 354

DGN/DGNC/DGNM-C : Used for parting of bars, hard materials and tough applications. A positive rake, single cavity with a negative land and shoulders. Medium-to-high feeds. DGNC - with coolant holes, DGNM - single ended for very deep applications. Features and Benefits A thin PVD coated TiCN layer on a P40 substrate High toughness and durability For general applications in parting and grooving steel at medium to high speedsSpecifications Grade: IC354 ISO Range - P/M/K: (P20-P40)(M10-M30) Grade or Coating Type: PVD Coating Layers: TiCNTypical Applications Parting Grooving Steel Steel alloys Stainless streel

GBP 25.99
1

CCMT 09T308-SM Insert Grade IC907

CCMT 09T308-SM Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 18.39
1

CCMT 09T302-SM Insert Grade IC907

CCMT 09T302-SM Insert Grade IC907

CCMT turning inserts are 80 rhombic shaped inserts. with a single-sided, 7 positive relief angle for semi-finish and finish cutting. "M" tolerance edge condition for general with chip breaking in moderate feed range. Their positive rake and low cutting forces make them ideal for use on a wide range of materials, including non-ferrous and exotic alloys. Features and Benefits A tough sub-micron substrate for durability and performance Good cutting performance at low-to-medium cutting speeds Suitable for use on heat resistant alloys, austenitic stainless steel and hard steel Standards Insert Grade IC907

GBP 18.39
1

DGN 4003C Insert Grade IC908

DGN 4003C Insert Grade IC908

DGN/DGNC/DGNM-C : Used for parting of bars, hard materials and tough applications. A positive rake, single cavity with a negative land and shoulders. Medium-to-high feeds. DGNC - with coolant holes, DGNM - single ended for very deep applications. Features and Benefits A hard, fine grain substrate with excellent chipping resistance New TiAlN PVD coating for added durability Provides high wear and oxidation resistance Recommended for a wide range of materials applications and machining conditionsSpecifications Grade: IC908 ISO Range - P/M/K: (P15-P30)(M20-M30)(K20-K40) ISO Range - H/S/N: (H10-H20)(S10-S25) Grade or Coating Type: PVD Coating Layers: TiAlNTypical Applications Parting Grooving

GBP 21.99
1

H600 WXCU 040310 HP Insert Grade IC330

H600 WXCU 040310 HP Insert Grade IC330

H600 WXCU Milling Inserts are double-sided 6 cutting edged inserts, for Fast Feed machining. Featuring a tough grade TiCN+TiN PVD coated with a 'SUMO TEC' surface treatment. Used for milling a wide range of work piece materials, at low to medium cuttingspeeds and for unstable machining conditions. Features and Benefits Coated with SUMO TEC surface treatment far added durability Features a tough grade TiCN+TiN PVD Double sided with 6 cutting edges for fast feed machining Specifications ISO Range - P/M/K: (P25-P40)(M30-M40) ISO Range - H/S/N: (S20-S30) Grade or Coating Type: PVD Coating Layers: TiCN+TiN Insert Grade : IC330 Typical Applications Milling

GBP 19.99
1

H600 WXCU 05T312HP Insert Grade IC330

H600 WXCU 05T312HP Insert Grade IC330

H600 WXCU Milling Inserts are double-sided 6 cutting edged inserts, for Fast Feed machining. Featuring a tough grade TiCN+TiN PVD coated with a 'SUMO TEC' surface treatment. Used for milling a wide range of work piece materials, at low to medium cuttingspeeds and for unstable machining conditions. Features and Benefits Coated with SUMO TEC surface treatment far added durability Features a tough grade TiCN+TiN PVD Double sided with 6 cutting edges for fast feed machining Specifications ISO Range - P/M/K: (P25-P40)(M30-M40) ISO Range - H/S/N: (S20-S30) Grade or Coating Type: PVD Coating Layers: TiCN+TiN Insert Grade : IC330 Typical Applications Milling

GBP 24.99
1

ADKT 150564R-HM Insert Grade IC328

ADKT 150564R-HM Insert Grade IC328

ADKT milling inserts features a tough substrate ideal for applications involving steel and stainless steel at low to medium cutting speeds and unstable machining conditions. The thin PVD TiCN coating helps provide excellent wear resistance and protection from heat build up, prolonging the tools lifespan. Features and Benefits Hard substrate for improved rigidity when machining PVD TiCN coating for improved heat and wear resistance Ideal for parting and grooving applications involving steel and stainless steel Specifications 85 Parallelogram Insert Insert Grade IC328 ISO Range - P/M/K: (P25-P40)(M30-M40) ISO Range -H/S/N/: (S20-S30) Grade or Coating Type: PVD Coating Layers: TiCN Typical Applications Milling Parting and Grooving

GBP 32.99
1

ADKT 1505PDTR-76 Insert Grade IC328

ADKT 1505PDTR-76 Insert Grade IC328

ADKT milling inserts features a tough substrate ideal for applications involving steel and stainless steel at low to medium cutting speeds and unstable machining conditions. The thin PVD TiCN coating helps provide excellent wear resistance and protection from heat build up, prolonging the tools lifespan. Features and Benefits Hard substrate for improved rigidity when machining PVD TiCN coating for improved heat and wear resistance Ideal for parting and grooving applications involving steel and stainless steel Specifications 85 Parallelogram Insert Insert Grade IC328 ISO Range - P/M/K: (P25-P40)(M30-M40) ISO Range -H/S/N/: (S20-S30) Grade or Coating Type: PVD Coating Layers: TiCN Typical Applications Milling Parting and Grooving

GBP 26.99
1

APKT 1604PDR-76 Insert Grade IC328

APKT 1604PDR-76 Insert Grade IC328

APKT 76 milling inserts feature thin PVD coated TiCN layer on a P45-K40 substrate for very high toughness. Ideal for milling, parting and grooving of steel, stainless and alloy steels at low to medium cutting speeds and for unstable machining conditions. Features and Benefits P45-K40 substrate for very high toughness PVD coated TiCN layer for greater heat and wear resistance Suitable for low to medium cutting speeds and unstable machining conditions 2 helical cutting edges with ribs along edge for interrupted cuts Typical Applications Milling Steel Stainless steel Alloy steels Standards Insert Grade : IC328 ISO Range - P/M/K: (P25-P40)(M30-M40) ISO Range - H/S/N: (S20-S30)

GBP 39.99
1

DGR 3102J-6D Insert Grade IC328

DGR 3102J-6D Insert Grade IC328

DGR/L-J/JS inserts are ideal for the parting and grooving of soft materials such as low carbon, alloy and austenitic stainless steel as well as the parting of tubes, small diameters and thin-walled parts at low-to-medium feeds. The JS inserts feature a sharp corner for effective cutting. Features and Benefits P445-K40 substrate provides very high toughness A thin PVD coated TiCN layer helps reduce the effects of wear and heat Ideal for applications involving low to medium cutting speeds and unstable machining conditions Typical Applications Milling Parting Grooving Steel Alloy steel Stainless steel Standards Grade: IC328 ISO Range - P/M/K: (P25-P40)(M30-M40) ISO Range - H/S/N: (S20-S30)

GBP 20.49
1

Tag N4C Insert Grade IC90 8

Tag N4C Insert Grade IC90 8

TAG N-C/W/M parting and grooving inserts are the first choice for the parting of bars, hard materials and tough applications. A positive rake, single cavity (except 7 & 12 mm with double cavity), negative land and shoulders, provides extra cutting-edge strength. Suitable for use with medium-to-high feeds. Features and Benefits Hard substrate construction for improved rigidity and strength Excellent chipping resistance properties TiAlN PVD coating provides high wear and oxidation resistance Specifications Grade : IC908 ISO Range - P/M/K: (P15-P30)(M20-M30)(K20-K40) ISO Range - H/S/N: (H10-H20)(S10-S25) Grade or Coating Type: PVD Coating Layers: TiAlN Typical Applications Milling Steel

GBP 23.99
1

H600 WXCU Indexable Milling Inserts

H600 WXCU Indexable Milling Inserts

Wiht theh H600 WXCU Milling Inserts, Iscar has merged three proven ideas into their new Helido Feedmill inserts for high-feed rough milling and cavity work in die & mold shops. The new H600 WXCU inserts feature helical cutting edges for smoother entry, 17 lead angles to reduce lateral forces and SUMO TEC surface treatment for longer edge life. Each trigon shaped insert provides six peripherally ground cutting edges and is seated securely into inclined dovetail pockets to prevent movement. Features and Benefits Coated with SUMO TEC surface treatment for added durability Features a tough grade TiCN+TiN PVD Double sided with 6 cutting edges for fast feed machining Typical Applications Milling Interrupted cutting Heavy machining operations Standards ISO Range - P/M/K: (P20-P40)(M35-M45) ISO Range - H/S/N: (S15-S30) Insert Grade : IC830

GBP 26.99
1