107 results (0,14694 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Advanced 20-VMMC120-ADV Single Relay Powered Output Module With Built In Isolator

Advanced 20-VMMC120-ADV Single Relay Powered Output Module With Built In Isolator

Advanced 20-VMMC120-ADV Single Relay Powered Output Module With Built In IsolatorThe single relay output module is loop-powered designed around a fully digital protocol and provides form C changeover contacts for control of equipment for DDA compliance such as vibrating pillows.The output channel is a normally de-energised relay switched on by a command from the control panel.The unit provides a fast and secure response and incorporates a bidirectional short circuit isolator. Connections are made using plug-in terminal blocks which will accept conductors up to 2.5mm .The unit can be mounted within an electrical box or enclosure.Key FeaturesShort circuit isolators in each device to the requirements of EN54-17Auto addressing capability by the control panel or manually using a hand-held programmerAuto-addressing capability by the control panelDigital checking of double addressLine quality informationBicolour redgreen LED driven by the control panel

GBP 78.97
1

Advanced MxPro5 MXP-544 P-BUS 8-Way Relay Card

Advanced MxPro5 MXP-544 P-BUS 8-Way Relay Card

Advanced MxPro5 MXP-544 P-BUS 8-Way Relay CardThe MXP-544 Peripheral 8-Way Relay Card is an internal module intended for use with the Mx-5000 range of fire alarm control panels.Each card provides 8 configurable relay outputs 2 x FORM C 6 x FORM A. Up to 16 cards may be connected to a panel allowing for an extra 128 relay outputs SELV.The MXP-544 is configured using a positive action sequence involving the on-board push button and LED indicators.This allows the module to be safely configuredinspected while adding an extra reporting capability not previously available to peripheral modules. Cards are protocol independent.Key FeaturesPowered from CIE on local PSUProvides 8 configurable relay outputsUp to 16 cards can be connected to the peripheral bus 128 relays

GBP 318.44
1

Advanced MxPro5 MXP-544F P-BUS 8-Way Relay Card Fitted

Advanced MxPro5 MXP-544F P-BUS 8-Way Relay Card Fitted

Advanced MxPro 5 MXP-544F P-BUS 8-Way Relay Card FittedThe MXP-544 Peripheral 8-Way Relay Card is an internal module intended for use with the Mx-5000 range of fire alarm control panels.Each card provides 8 configurable relay outputs 2 x FORM C 6 x FORM A. Up to 16 cards may be connected to a panel allowing for an extra 128 relay outputs SELV.The MXP-544 is configured using a positive action sequence involving the on-board push button and LED indicators.This allows the module to be safely configuredinspected while adding an extra reporting capability not previously available to peripheral modules. Cards are protocol independent.Key FeaturesPowered from CIE on local PSUProvides 8 configurable relay outputsUp to 16 cards can be connected to the peripheral bus 128 relays

GBP 318.44
1

Advanced 20-VMC100-ADV Single Relay Powered Output Module With Built In Isolator

Advanced 20-VMC100-ADV Single Relay Powered Output Module With Built In Isolator

Advanced 20-VMC100-ADV Single Relay Powered Output Module With Built In IsolatorThe single output module is loop powered designed around a fully digital protocol and provides control by activating equipment for DDA compliance such as vibrating pillows. The output channel is monitored and will detect open and short circuit conditions.The unit provides a fast and secure response and incorporates a bidirectional short circuit isolator. Connections are made using plug-in terminal blocks which will accept conductors up to 2.5mm.The unit is supplied fixed to a plate which is suitable for wall mounting. Standard 25mm or deep 47mm mounting boxes are available.Key FeaturesShort circuit isolators in each device to the requirements of EN54- 17Auto addressing capability by the control panel or manually using a handheld programmerDigital checking of double addressLine quality informationBicolour red green LED driven by the control panel

GBP 131.62
1

Advanced Programmable Relay - MXP-035

Advanced Programmable Relay - MXP-035

Advanced Programmable Relay - MXP-035The programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits. Up to 16 Cards can be connected to a multi-loop control panel providing a maximum of up to 64 additional local relay outputs. Each output is fully programmable using the powerful DynamiX cause and effects rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 1A power supply.Key Features4 Way Programmable Relay Card16 Cards Max per Control panel totalling 64 230V 5 Amp rated outputsEasily Configured via PC-NET-0033 Year Warranty as standard

GBP 279.74
1

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052The Mxp-052 is a peripheral relay card providing ten 30V DC 1A programmable relay outputs. The Mxp-052 connects directly to any of the DIL connectors of either the Network Mimic Mxp-020-100 LED Output Card or the General IO controller Mxp-045 LED Output Card units via the supplied ribbon cable.Each output follows the cause and effect programming of the mimic unit output. This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the Mx-40005000 systems Dynamix zoning facilities.Key FeaturesTen change-over contact outputs rated at 30V DC 1A.Up to 200 individual relay outputs fully programmable per mimic excluding LEDsTen individually programmable relay outputs per unitDIN rail or screw fixing optionsSeparate isolate input disables all outputsSeparate isolate indication outputFast instant responseProduct CodesDescriptionMXP-052Mimic driven 10-way relay output cardMXP-052-DINMimic driven 10-way relay output card in din-rail carrier

GBP 129.16
1

Advanced Spare Zone Active End-of-Line Module Pack of 5 EXP-006

Advanced Spare Zone Active End-of-Line Module Pack of 5 EXP-006

Spare Zone Active End-of-Line Module pack of 5 EXP-006The EXP-006 module provides active end of line monitoring for zone circuits fitted with detector diode bases in accordance with BS5839-1 the module will create a fault condition on the panel if a detector is removed from its base without affecting the remainder of the zone.CompatibilityCompatible with the ExGo Series Gas Extinguishing Panel input circuits.LimitationsFor use in gas extinguishing installations where an EOL module is required.

GBP 61.18
1

Advanced MXP-507 2-Way Relay Card MxPro 5

Advanced MXP-507 2-Way Relay Card MxPro 5

Advanced MXP-507 2-Way Relay Card MxPro 5The 2-Way Programmable Relay Card2-Way Relay Output Card is an internal peripheral for use with MxPro 5 series control panels.This additional PCB provides a cost-effective solution to providing 2 individually programmable 1 Amp rated volt free change over contacts.The 2-Way Programmable Relay Cardconnects directly to the panels motherboard in which each output can be individually assigned to an output group to provide full support for dynamic zoning.ApplicationsIdeal for any application where a number of programmable outputs are required at the panel e.g. landlordtenant interfaces.The system can to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key FeaturesEach output individually programmableOptional fail-safe setupAllow investigation delaysCan silence optionInstant response timeCost effective against ancillary hardwareEach output 30V ACDC 1 Amp rating3 year warranty as standard

GBP 118.54
1

Advanced ExGo 2 Way Relay Output Card - EXP-007

Advanced ExGo 2 Way Relay Output Card - EXP-007

Advanced ExGo 2 Way Relay Output Card - EXP-007The 2 or 8 Way Relay Output Card is an internal peripheral for use with The ExGo series control panels and status indicators. This additional PCB provides a cost effective solution to providing 2 or 8 individually programmable 1 Amp rated volt free clean contact outputs. The 2 or 8 Way Relay Output Card connects directly to the panels motherboard in which each output can be individually programmed. Ideal for any application where a number of programmable outputs are required at the panel. The features of the 2 or 8 Way Relay Output Card not only aid commissioning and cut down on expensive ancillary hardware but also allow the system to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key Features2 Individual Programmable OutputsFast Instant ResponseEach Output 30V ACDC 1 Amp RatingCost effective against ancillary hardware

GBP 120.76
1

Advanced MxPro 5 MXP-507F 2-Way Relay Card Fitted

Advanced MxPro 5 MXP-507F 2-Way Relay Card Fitted

Advanced MxPro 5 MXP-507F 2-Way Relay Card FittedThe 2-Way Programmable Relay Card2-Way Relay Output Card is an internal peripheral for use with MxPro 5 series control panels.This additional PCB provides a cost-effective solution to providing 2 individually programmable 1 Amp rated volt free change over contacts.The 2-Way Programmable Relay Cardconnects directly to the panels motherboard in which each output can be individually assigned to an output group to provide full support for dynamic zoning.ApplicationsIdeal for any application where a number of programmable outputs are required at the panel e.g. landlordtenant interfaces.The system can to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key FeaturesEach output individually programmableOptional fail-safe setupAllow investigation delaysCan silence optionInstant response timeCost effective against ancillary hardwareEach output 30V ACDC 1 Amp rating3-year warranty as standard

GBP 118.54
1

Advanced MxPro MXP-035F Peripheral Bus - 4-Way Relay Card Fitted

Advanced MxPro MXP-035F Peripheral Bus - 4-Way Relay Card Fitted

Advanced MxPro MXP-035F Peripheral Bus - 4-Way Relay Card FittedThe Programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits.Up to 16 cards can be connected to a multi-loop control panel providing a maximum of up to 64 additional local relay outputs.Each output is fully programmable using the powerful dynamic cause-and-effects rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 1A power supply.Applications Limitations Plant control and signalling outputs. Each output can be assigned to an individual output group and is fully programmable for any output function allowed within the MxPro 4 configuration program.Fitting of the Programmable 4-Way Relay Cardin a panel precludes fitting of other panel option cards. Requires installation of the Peripheral Bus Interface Card in the panel when using the MxPro 4 series.Key FeaturesEach output is 230V 5A ratedEach output is individually programmable with any of the available DynamiX cause-and-effect rulesUp to 16 cards can be connected providing a total of 64 additional outputsEach output may be individually programmedAn input is provided to monitor the fault output from a power supply.4-way programmable relay cardEasily configured via PC-NET-0033-year warranty as standard

GBP 279.74
1

Advanced ExGo 8 Way Relay Output Card - EXP-008

Advanced ExGo 8 Way Relay Output Card - EXP-008

Advanced ExGo 8 Way Relay Output Card - EXP-008The 2 or 8 Way Relay Output Card is an internal peripheral for use with The ExGo series control panels and status indicators. This additional PCB provides a cost effective solution to providing 2 or 8 individually programmable 1 Amp rated volt free clean contact outputs.The 2 or 8 Way Relay Output Card connects directly to thepanels motherboard in which each outputcan be individually programmed.Ideal for any application where a number of programmable outputs are required at the panel. The features of the 2 or 8 Way Relay Output Card not only aid commissioning and cut down on expensive ancillary hardware but also allow the system to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key Features2 or 8 individual programmable outputsEach output individually programmableFast responseEach output 30V ACDC 1 Amp ratingCost effective against ancillary hardwareOptional fail-safe setupEasily programmable by on board keypadPlease Note This is to be used with theAdvanced EX-3001 ExGo Three Zone Automatic Gas Extinguishing Panel only.

GBP 258.78
1

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail Carrier

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail Carrier

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail CarrierThe Peripheral Relay Card provides 10 30V DC 1A programmable relay outputs.The Peripheral Relay Card connects directly to any of the DIL connectors of either the Network Mimic 100 LED Output Card or the Multi way InputOutput Card unit via the supplied ribbon cable.Each output follows the cause-and-effect programming of the mimic unit output.This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the MxPro5 Dynamic zoning facilities.Key FeaturesTen change-over contacts outputs at 30Vdc 1ADIN rail fixingSeparate isolate input disables all outputsSeparate isolate indication outputFast response

GBP 149.43
1

Advanced ELRL240 Enclosed Hold-Off Relay with Built-In Delay

Advanced ELRL240 Enclosed Hold-Off Relay with Built-In Delay

Advanced ELRL240Enclosed Hold-Off Relay with Built-In DelayOn some installations it can sometimes be more advantageous to provide the emergency lighting from static inverter or central battery system. On systems using static inverters it is sometimes necessary for the normal supply and static inverter supply to be selected automatically by a switching device either within or external to the luminaire. The ELRL240 hold off relay provides a simple solution to this requirement. When a site uses a static inverter it is not always tied to the grid frequency and could even be antiphase with the normal supply. When a relay tries to switch between these supplies there is a tendency for the relay to suffer from arcing between the normally open and normally closed contacts resulting in temporary short circuit between the two out of phase supplies. This will cause external circuit protection to operate. Because the device uses two interposing relays for the two supplies and introduces a time delay of approximately 500mS between breaking the normal supply and connecting the static inverter supply the device removes any risk of arcing across contacts due to phase differences between the two supplies. This is also reversed when the static inverter supply is removed and a similar delay is introduced prior to reconnection to the normal lighting supply.A dimming isolation facility is incorporated as standard for use with dimming ballasts to enable full light output to be achieved in the emergency condition.Key FeaturesEnhanced change-over relay for static inverter supplied luminairesAutomatic time delay to avoid arcing during change-overBuilt in dimming isolation feature

GBP 89.94
1

Advanced MxPro MXP-035-BXP Peripheral Bus - 4-Way Relay Card with 1.5A PSU Boxed

Advanced MxPro MXP-035-BXP Peripheral Bus - 4-Way Relay Card with 1.5A PSU Boxed

Advanced MxPro MXP-035-BXP Peripheral Bus - 4-Way Relay Card with 1.5A PSU BoxedThe Programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits.Up to 16 cards can be connected to a multi-loop control panel providing a maximum of up to 64 additional local relay outputs.Each output is fully programmable using the powerful dynamic cause-and-effects rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 1A power supply.Applications Limitations Plant control and signalling outputs. Each output can be assigned to an individual output group and is fully programmable for any output function allowed within the MxPro 4 configuration program.Fitting of the Programmable 4-Way Relay Cardin a panel precludes fitting of other panel option cards. Requires installation of the Peripheral Bus Interface Card in the panel when using the MxPro 4 series.Key FeaturesEach output is 230V 5A ratedEach output is individually programmable with any of the available DynamiX cause-and-effect rulesUp to 16 cards can be connected providing a total of 64 additional outputsEach output may be individually programmedAn input is provided to monitor the fault output from a power supply.4-way programmable relay cardEasily configured via PC-NET-0033-year warranty as standard

GBP 466.21
1

Advanced AXIS-WSM Intelligent Sounder Interface Module

Advanced AXIS-WSM Intelligent Sounder Interface Module

Advanced AXIS-WSM Intelligent Sounder Interface ModuleThe Intelligent Sounder Interface Module is designed to allow the use of the Axis-CWS conventional sounder and Axis-CWSV conventional sounder beacon on an EvacGo intelligent loop.The Axis-WSM module is compatible with intelligent control panels and systems using Axis EN protocol. Easy to install it incorporates built-in short circuit loop isolation.Once installed onto an EvacGo intelligent loop the device is fully addressable and benefits from an extensive range of intelligent control and monitoring functionality.Key FeaturesFlexible modular designEasy to installManual and auto addressing optionsBuilt-in short circuit isolatorsUp to 32 tones as standardOptional microphone self-test facilityAddressing using the device programming tool or auto addressing capability via the fire control panelFits EvacGo modular wall sounders and sounder beacons

GBP 40.80
1