migliori trattamenti per lassità cutanea from GBP 13 | See the cheapest prices and offers on Cobiro CSS.com

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052The Mxp-052 is a peripheral relay card providing ten 30V DC 1A programmable relay outputs. The Mxp-052 connects directly to any of the DIL connectors of either the Network Mimic Mxp-020-100 LED Output Card or the General IO controller Mxp-045 LED Output Card units via the supplied ribbon cable.Each output follows the cause and effect programming of the mimic unit output. This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the Mx-40005000 systems Dynamix zoning facilities.Key FeaturesTen change-over contact outputs rated at 30V DC 1A.Up to 200 individual relay outputs fully programmable per mimic excluding LEDsTen individually programmable relay outputs per unitDIN rail or screw fixing optionsSeparate isolate input disables all outputsSeparate isolate indication outputFast instant responseProduct CodesDescriptionMXP-052Mimic driven 10-way relay output cardMXP-052-DINMimic driven 10-way relay output card in din-rail carrier

GBP 129.16

1

Advanced Sounder Splitter Card - MXS-021

Advanced Sounder Splitter Card - MXS-021The Mxs-021 Sounder Circuit Splitter is a peripheral unit for use with all MxPro4 range of control Panels. This additional unit takes a standard sounder circuit from either a control panel or other panel based sounder circuit controller and multiplies to provide up to 4 monitored outputs. In operation the additional outputs follow the output they are connected to. The circuits are fully monitored for open and short circuit and will take an independent supply to provide up to 1A per circuit.Key Features4 Monitored Outputs3 Year Warranty as standardUp to 1 Amp per circuitCost effective against ancillary hardwareCompatibilityThe Sounder Splitter Cardis compatible with all MxPro 4 controlpanels.LimitationsThe 4-way sounder splitter card can be supplied as a PCB only for mounting. When supplied fitted in this format the load at the outputs from the splitter will be limited to the sounder output loading of the input circuit from which it is driven.All 4 outputs on the sounder splitter card will operate in tandem and follow the output of the sounder circuit to which the card is connected.

GBP 127.68

1

Advanced Programmable Relay - MXP-035

Advanced Programmable Relay - MXP-035The programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits. Up to 16 Cards can be connected to a multi-loop control panel providing a maximum of up to 64 additional local relay outputs. Each output is fully programmable using the powerful DynamiX cause and effects rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 1A power supply.Key Features4 Way Programmable Relay Card16 Cards Max per Control panel totalling 64 230V 5 Amp rated outputsEasily Configured via PC-NET-0033 Year Warranty as standard

GBP 224.15

1

Advanced LX-9403 Lux Intelligent Control Panel with Three Loop Cards

Advanced LX-9403 Lux Intelligent Control Panel with Three Loop CardsThe Advanced Lux Intelligent Addressable Emergency Lighting Control System is designed to provide a simple yet powerful reliable and cost-effective maintenance solution for testing your emergency lights and maintaining results data for inspection and audit purposes. It supports both maintained non-maintained and slave luminaires in either self-contained central battery or static inverter systems. It supports all of the Advanced Lux Intelligent range of fittings. On top of this Lux Intelligent addressable modules can be added to almost any luminaires to allow them to function on the Lux Intelligent system fully.The control panel has a dynamic event log of 1000 events as well as a separate log for the recording of test results. Records of all automatic and manual tests are generated and can be downloaded byconnecting to a computer and using the appropriate Lux Intelligent Logger tool. The data is then transferred to a database on a PC for subsequent analysis listing and printing. There is also the opportunity of transferring this information up to the Lux Intelligent Cloud using the Lux Intelligent sync tool.Key FeaturesAnalogue addressable emergency lighting test panelUp to four loops per panelUp to 249 luminaires per loopPanel easily networked into 200 node networksEasily installed often on existing wiringCompatible with most third party luminaires including most modern LED lightsEasy conversion of existing lights with our addressable modulesAvailable with complete range of addressable lightsCan work with and monitor central battery and static inverter systems5 Amp power supplyLCD interface for onboard programming and managementOptional onboard printerAutolearn and loop detection for trouble-free installation and configurationPC management software

GBP 1657.41

1

Advanced LX-9404 Lux Intelligent Control Panel with Four Loop Cards

Advanced LX-9404 Lux Intelligent Control Panel with Four Loop CardsThe Advanced Lux Intelligent Addressable Emergency Lighting Control System is designed to provide a simple yet powerful reliable and cost-effective maintenance solution for testing your emergency lights and maintaining results data for inspection and audit purposes. It supports both maintained non-maintained and slave luminaires in either self-contained central battery or static inverter systems. It supports all of the Advanced Lux Intelligent range of fittings. On top of this Lux Intelligent addressable modules can be added to almost any luminaires to allow them to function on the Lux Intelligent system fully.The control panel has a dynamic event log of 1000 events as well as a separate log for the recording of test results. Records of all automatic and manual tests are generated and can be downloaded byconnecting to a computer and using the appropriate Lux Intelligent Logger tool. The data is then transferred to a database on a PC for subsequent analysis listing and printing. There is also the opportunity of transferring this information up to the Lux Intelligent Cloud using the Lux Intelligent sync tool.Key FeaturesAnalogue addressable emergency lighting test panelUp to four loops per panelUp to 249 luminaires per loopPanel easily networked into 200 node networksEasily installed often on existing wiringCompatible with most third party luminaires including most modern LED lightsEasy conversion of existing lights with our addressable modulesAvailable with complete range of addressable lightsCan work with and monitor central battery and static inverter systems5 Amp power supplyLCD interface for onboard programming and managementOptional onboard printerAutolearn and loop detection for trouble-free installation and configurationPC management software

GBP 1841.71

1

Advanced LX-9402 Lux Intelligent Control Panel with Two Loop Cards

Advanced LX-9402 Lux Intelligent Control Panel with Two Loop CardsThe Advanced Lux Intelligent Addressable Emergency Lighting Control System is designed to provide a simple yet powerful reliable and cost-effective maintenance solution for testing your emergency lights and maintaining results data for inspection and audit purposes. It supports both maintained non-maintained and slave luminaires in either self-contained central battery or static inverter systems. It supports all of the Advanced Lux Intelligent range of fittings. On top of this Lux Intelligent addressable modules can be added to almost any luminaires to allow them to function on the Lux Intelligent system fully.The control panel has a dynamic event log of 1000 events as well as a separate log for the recording of test results. Records of all automatic and manual tests are generated and can be downloaded byconnecting to a computer and using the appropriate Lux Intelligent Logger tool. The data is then transferred to a database on a PC for subsequent analysis listing and printing. There is also the opportunity of transferring this information up to the Lux Intelligent Cloud using the Lux Intelligent sync tool.Key FeaturesAnalogue addressable emergency lighting test panelUp to four loops per panelUp to 249 luminaires per loopPanel easily networked into 200 node networksEasily installed often on existing wiringCompatible with most third party luminaires including most modern LED lightsEasy conversion of existing lights with our addressable modulesAvailable with complete range of addressable lightsCan work with and monitor central battery and static inverter systems5 Amp power supplyLCD interface for onboard programming and managementOptional onboard printerAutolearn and loop detection for trouble-free installation and configurationPC management software

GBP 1473.12

1

Advanced LX-9401 Lux Intelligent Control Panel with One Loop Card

Advanced LX-9401 Lux Intelligent Control Panel with One Loop CardThe Advanced Lux Intelligent Addressable Emergency Lighting Control System is designed to provide a simple yet powerful reliable and cost-effective maintenance solution for testing your emergency lights and maintaining results data for inspection and audit purposes. It supports both maintained non-maintained and slave luminaires in either self-contained central battery or static inverter systems. It supports all of the Advanced Lux Intelligent range of fittings. On top of this Lux Intelligent addressable modules can be added to almost any luminaires to allow them to function on the Lux Intelligent system fully.The control panel has a dynamic event log of 1000 events as well as a separate log for the recording of test results. Records of all automatic and manual tests are generated and can be downloaded byconnecting to a computer and using the appropriate Lux Intelligent Logger tool. The data is then transferred to a database on a PC for subsequent analysis listing and printing. There is also the opportunity of transferring this information up to the Lux Intelligent Cloud using the Lux Intelligent sync tool.Key FeaturesAnalogue addressable emergency lighting test panelUp to four loops per panelUp to 249 luminaires per loopPanel easily networked into 200 node networksEasily installed often on existing wiringCompatible with most third party luminaires including most modern LED lightsEasy conversion of existing lights with our addressable modulesAvailable with complete range of addressable lightsCan work with and monitor central battery and static inverter systems5 Amp power supplyLCD interface for onboard programming and managementOptional onboard printerAutolearn and loop detection for trouble-free installation and configurationPC management software

GBP 1288.79

1

Advanced MxPro 5 MXP-511F Access Enable Key Switch Fitted

Advanced MxPro 5 MXP-511F Access Enable Key Switch FittedTheMxPro 5control panel range supportsdirect installation of up to 8 individual key switches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.CompatibilityCan be used with allMxPro 5series control panels.LimitationsIf an on-board printer is fitted to the MxPro 5 2 4 loop control panels then the maximum number of switches fitted is limited to 4. If the MxPro 5 3 position switch is fitted then two programmable inputs must be available per switch.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switches

GBP 79.00

1

Advanced MX-5000 - 3-Pos Key Switch - trapped MXP-515

Advanced MX-5000 - 3-Pos Key Switch - trapped MXP-515TheMxPro 5control panel range supportsdirect installation of up to 8 individual keyswitches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switchesCompatibilityCan be used with allMxPro 5series control panels.LimitationsIf an on-board printer is fitted to the MxPro 5 2 4 loop control panels then the maximum number of switches fitted is limited to 4. If the MxPro 5 3 position switch is fitted then two programmable inputs must be available per switch.

GBP 55.96

1

Advanced MX-5000 - 2-Pos Key Switch - untrapped MXP-517

MX-5000 - 2-Pos Key Switch - untrapped MXP-517TheMxPro 5control panel range supportsdirect installation of up to 8 individual key switches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switchesCompatibilityCan be used with allMxPro 5series control panels.LimitationsIf an on-board printer is fitted to the MxPro 5 2 4 loop control panels then the maximum number of switches fitted is limited to 4. If the MxPro 5 3 position switch is fitted then two programmable inputs must be available per switch.

GBP 55.96

1

Advanced MxPro 5 MXP-536F 8-Way Programmable Zone Monitor Card Fitted

Advanced MxPro 5 MXP-536F 8-Way Programmable Zone Monitor Card FittedThe Programmable 8-Zone Monitor Card is an optional peripheral unit that provides eight individually programmable zone monitor circuits compliant with BSEN54- 18 1998 Clause 7.8.Up to 16 cards can be connected to a multi-loop panel providing a maximum of up to 128 additional zone monitor circuits.Each zone is fully programmable using the powerful dynamic cause-and-effect rules.The unit is available as either a printed circuit card only.Applications LimitationsEN54-18 compliant zone monitor circuit.Key Features8 zone circuits - each zone is monitored for open and short circuitEach zone is individually programmable with the available dynamic cause-and-effect rulesUp to 16 cards can be connected giving a total of 128 additional zone monitors1 relay output for reset128 zone monitor circuits per panelEasily configured via PC-NET-0033 year warranty as standard

GBP 374.84

1

Advanced MxPro 5 MXP-536 P-BUS 8 Way Conventional Zone Card

Advanced MxPro 5 MXP-536 P-BUS 8 Way Conventional Zone CardThe Programmable 8-Zone Monitor Card is an optional peripheral unit that provides eight individually programmable zone monitor circuits compliant with BSEN54- 18 1998 Clause 7.8. Up to 16 cards can be connected to a multi-loop panel providing a maximum of up to 128 additional zone monitor circuits. Each zone is fully programmable using the powerful dynamic cause-and-effect rules. The unit is available as either a printed circuit card only.Applications LimitationsEN54-18 compliant zone monitor circuit.Key Features8 zone circuits - each zone is monitored for open and short circuitEach zone is individually programmable with the available dynamic cause-and-effect rulesUp to 16 cards can be connected giving a total of 128 additional zone monitors1 relay output for reset128 zone monitor circuits per panelEasily configured via PC-NET-0033 year warranty as standard

GBP 374.84

1

Advanced MXS-511-KEY Spare MXP-511 Access Enable Key

Advanced MXS-511-KEY Spare MXP-511 Access Enable KeyThe Advanced MXS-511-KEY is a spare Mxp-511 Access Enable KeyThe MxPro 5 control panel range supports direct installation of up to 8 individual keyswitches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.CompatibilityCan be used with all MxPro 5 series control panels.LimitationsIf an on-board printer is fitted to the MxPro 5 2 4 loop control panels then the maximum number of switches fitted is limited to 4.If the MxPro 5 3 position switch is fitted then two programmable inputs must be available per switch.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switches

GBP 12.52

1

Advanced MxPro5 MXP-547 ESPA Pager Interface

Advanced MxPro5 MXP-547 ESPA Pager InterfaceThe Pager Interface is a programmable interface providing connectivity of third party paging systems to the MxPro 5 control equipment. It utilises the industry standard protocol ESPA 4.4.4 and connects to the equipment via a serial data connection. An optional input function is available to monitor pager fault conditions. Specific event types e.g. Fire Alarm Pre- Alarm Fault etc. can be sent to individual pagers andor to groups of pagers.Applications LimitationsFor use with pager systems compliant to ESPA 4.4.4 protocol. If a printer is also required fit an internal printer assembly.Key FeaturesUp to 8 configurable shifts per weekdayweekendUp to 50 pager groupsUp to 250 pager addressesEach pager address can be configured to cover 2 zone rangesZone andor point information can be sent to the pagerUser defined texts are available and the basic event type text can be configuredESPA 4.4.4 protocolPanel mounted or boxed versionEasily configured via pager PC Software3 year warranty as standard

GBP 733.23

1

Advanced MxPro5 MXP-547-BX ESPA Pager Interface Boxed

Advanced MxPro5 MXP-547-BX ESPA Pager Interface BoxedThe Pager Interface is a programmable interface providing connectivity of third party paging systems to the MxPro 5 control equipment. It utilises the industry standard protocol ESPA 4.4.4 and connects to the equipment via a serial data connection. An optional input function is available to monitor pager fault conditions. Specific event types e.g. Fire Alarm Pre- Alarm Fault etc. can be sent to individual pagers andor to groups of pagers.Applications LimitationsFor use with pager systems compliant to ESPA 4.4.4 protocol. If a printer is also required fit an internal printer assembly.Key FeaturesUp to 8 configurable shifts per weekdayweekendUp to 50 pager groupsUp to 250 pager addressesEach pager address can be configured to cover 2 zone rangesZone andor point information can be sent to the pagerUser defined texts are available and the basic event type text can be configuredESPA 4.4.4 protocolPanel mounted or boxed versionEasily configured via pager PC Software3 year warranty as standardBoxed

GBP 845.23

1

Advanced MxPro 5 MXP-538 P-BUS 16-Way Switch Form Factor Module

Advanced MxPro 5 MXP-538 P-BUS 16-Way Switch Form Factor ModuleThe 16-way Switch 48 LED Card is an expansion peripheral that offers 16 inputs and 48 outputs that can be configured via the Advanced PC Config Tool. This additional PCB provides a cost effective solution to providing 16 individually programmable push buttons for controlling fire alarm equipment.Up to 16 cards can be connected to a MxPro 5 series panel providing a maximum of 256 push buttons and 768 LED outputs. Each LED output can be individually assigned to an output group to provide full support for dynamic zoning and to indicate when the buttons have been activated.ApplicationsIdeal for any application where a number of programmable push button switches are required for evacuation and plant control.Key Features16 configurable push buttons48 Programmable LEDs 3 x LEDs per push button red green yellowConfigurable buzzerFast input responseUp to 16 switch plates for each control panel

GBP 360.18

1

Advanced Dynamix MxPro PC-NET-005-SWM15 Smart Watch Module 7-15 panel

Advanced Dynamix MxProPC-NET-005-SWM15 Smart Watch Module 7-15 panelThe Smart Watch Module SWM is a device used in conjunction with the PC-Net Graphical Software Suite offered by Advanced and is used for the control and diagnostics of remote site applications.The Smart Watch Module SWM uses Static TCPIP addressing over Local Area Network LAN or Wide Area Network WAN applications limiting the need for additional cabling and allowing remote sites to be monitored over a network fromacentrally located Graphical Software Suite.The Smart Watch Modules SWM cleveruse of TCPIP technology provides the user with an ultimate level of control for all their Fire products worldwide.The SWM is supplied in two variations one for remote control and diagnostics of Addressable System Installations and the other for Conventional.Key FeaturesSmall and CompactRemote Network Control DiagnosticsPowerTCPIP Communication via Static IPDirect connectivity to BMSGraphical Interface via RS232Connect up to 255 Remote SitesSupports up to 15 remote panels per siteConfigured using Graphical Software

GBP 3781.66

1

Advanced MxPro5 MXP-547F ESPA Pager Interface Fitted

Advanced MxPro5 MXP-547F ESPA Pager Interface FittedThe Pager Interfaceis a programmable interface providing connectivity of third-party paging systems to the MxPro 5 control equipment.It utilises the industry standard protocol ESPA 4.4.4 and connects to the equipment via a serial data connection. An optional input function is available to monitor pager fault conditions.Specific event types e.g. Fire Alarm Pre- Alarm Fault etc. can be sent to individual pagers andor to groups of pagers.Applications LimitationsFor use with pager systems compliant to ESPA 4.4.4 protocol. If a printer is also required fit an internal printer assembly.Key FeaturesUp to 8 configurable shifts per weekdayweekendUp to 50 pager groupsUp to 250 pager addressesEach pager address can be configured to cover 2 zone rangesZone andor point information can be sent to the pagerUser defined texts are available and the basic event type text can be configuredESPA 4.4.4 protocolPanel mounted or boxed versionEasily configured via pager PC Software3-year warranty as standard

GBP 733.23

1

Advanced MXP-034 Peripheral Bus - 4-Way Sounder Card

Advanced MXP-034 Peripheral Bus - 4-Way Sounder CardThe Programmable 4-Way Sounder Card is an optional peripheral unit that provides four individually programmable and monitored sounder output circuits compliant with BSEN54-2 1998 Clause 7.8.Up to 16 Cards can be connected to a multi-loop panel providing a maximum of 64 additional local sounder outputs.Each output is fully programmable using the powerful DynamiX Cause and Effect rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 4A power supply.Key Features4 Way Programmable Sounder Card16 cards max per Control panel totalling 64 1 Amp rated outputsEasily configured via PC-NET-0033 Year Warranty as standardFully SynchronisedEach output is 1A rated and monitored for open and short circuitsEach output is individually programmable using the Dynamix cause-and-effects rulesAll outputs can be synchronised in pulsing modesUp to 16 cards can be connected giving a total of 64 additional outputsEach output may be individually programmed

GBP 252.01

1

Advanced Remote Status Indicator LCD LED Indicators with Mode Select Key Switch EX-3021

Advanced Remote Status Indicator LCD LED Indicators with Mode Select Key Switch EX-3021The Ex Remote Status Indicators are available in two formats a basic display only with optional key switches or a manual release version with optional keyswitch for automaticmanual mode. The Ex-extinguishing system detects a fire in the same manner as a fire alarm system but in addition to sounding alarms it also controls the release of an extinguishing agent.The extinguishing agent can take many forms from CO through to specialist gasses developed solely for extinguishing purposes. The agent is released into the atmosphere in the area where a fire has been detected reducing the density of oxygen in the atmosphere around the fire thus extinguishing the fire. The Ex-extinguishing system is used primarily in areas of significant valuestrategic importance to businesses e.g. computer suites telecom switch-rooms thus providing a cost effective solution to protect your work place.Key FeaturesSmall and compactRS485 network portOptional manual release or display onlySurface mount or semi-flush optionUp to 7 remote status indicators per one ExGo 1 loop panel3 year warranty as standardKey switch option for mode select or enable controlsMultiple languagesProgrammable inputs outputs

GBP 184.11

1

Advanced Semi-Flushing Bezel for Remote Status Indicator EXM-002

Advanced Semi-Flushing Bezel for Remote Status IndicatorEXM-002The Ex Remote Status Indicators are available in two formats a basic display only with optional key switches or a manual release version with optional key switch for automaticmanual mode.The Ex-extinguishing system detects a fire in the same manner as a fire alarm system but in addition to sounding alarms it also controls the release of an extinguishing agent.The extinguishing agent can take many forms from CO through to specialist gases developed solely for extinguishing purposes.The agent is released into the atmosphere in the area where a fire has been detected reducing the density of oxygen in the atmosphere around the fire thus extinguishing the fire.The Ex-extinguishing system is used primarily in areas of significant valuestrategic importance to businesses e.g. computer suites and telecom switch-rooms thus providing a cost-effective solution to protect your work place.Key FeaturesSmall and compactRS485 network portOptional manual release or display onlySurface mount or semi-flush optionUp to 7 remote status indicators per one ExGo 1 loop panel3-year warranty as standardKey switch option for mode select or enable controlsMultiple languagesProgrammable inputs and outputs

GBP 53.29

1

Advanced Remote Status Indicator LCD LED Indicators with Release Button Mode Select Key Switch EX-3031

Advanced Remote Status Indicator LCD LED Indicators with Release Button Mode Select Key Switch EX-3031The Ex Remote Status Indicators are available in two formats a basic display only with optional key switches or a manual release version with optional keyswitch for automaticmanual mode. The Ex-extinguishing system detects a fire in the same manner as a fire alarm system but in addition to sounding alarms it also controls the release of an extinguishing agent.The extinguishing agent can take many forms from CO through to specialist gasses developed solely for extinguishing purposes. The agent is released into the atmosphere in the area where a fire has been detected reducing the density of oxygen in the atmosphere around the fire thus extinguishing the fire. The Ex-extinguishing system is used primarily in areas of significant valuestrategic importance to businesses e.g. computer suites telecom switch-rooms thus providing a cost effective solution to protect your work place.Key FeaturesSmall and compactRS485 network portOptional manual release or display onlySurface mount or semi-flush optionUp to 7 remote status indicators per one ExGo 1 loop panel3 year warranty as standardKey switch option for mode select or enable controlsMultiple languagesProgrammable inputs outputs

GBP 212.09

1

Advanced Ex-3030 Remote Status Indicator Panel with LCD LED and Manual Release Button

Advanced Ex-3030 Remote Status Indicator Panel with LCD LED and Manual Release ButtonThe Remote Status Indicators are available in two formats a basic display only with optional key switches or a manual release version with optional key-switch for automaticmanual mode. The Ex-Extinguishing system detects a fire in the same manner as a fire alarm system but in addition to sounding alarms it also controls the release of an extinguishing agent. The extinguishing agent can take many forms from CO through to specialist gasses developed solely for extinguishing purposes.The agent is released into the atmosphere in the area where a fire has been detected reducing the density of oxygen in the atmosphere around the fire thus extinguishing the fire. The Ex-Extinguishing system is used primarily in areas of significant valuestrategic importance to businesses e.g. computer suites telecom switch-rooms thus providing a cost effective solution to protect your work place.FeaturesRS485 Network PortSmall and CompactOptional Manual Release or Display OnlySurface Mount or Semi Flush OptionUp to 7 Remote Status Indicators per one Ex-3001 Panel3 Year Warranty as standardKey Switch Option for mode select or enable controlsMultiple LanguagesSlide In Labels

GBP 194.60

1

Advanced Remote Status Indicator Panel with LCD and LED Indicators EX-3020

Advanced Remote Status Indicator Panel with LCD and LED Indicators EX-3020The Remote Status Indicators are available in two formats a basic display only with optional key switches or a manual release version with optional key-switch for automaticmanual mode. The Ex-Extinguishing system detects a fire in the same manner as a fire alarm system but in addition to sounding alarms it also controls the release of an extinguishing agent. The extinguishing agent can take many forms from CO through to specialist gasses developed solely for extinguishing purposes.The agent is released into the atmosphere in the area where a fire has been detected reducing the density of oxygen in the atmosphere around the fire thus extinguishing the fire. The Ex-Extinguishing system is used primarily in areas of significant valuestrategic importance to businesses e.g. computer suites telecom switch-rooms thus providing a cost effective solution to protect your work place.Key FeaturesRS485 Network PortSmall and CompactOptional Manual Release or Display OnlySurface Mount or Semi Flush OptionUp to 7 Remote Status Indicators per one Ex-3001 Panel3 Year Warranty as standardKey Switch Option for mode select or enable controlsMultiple LanguagesSlide In Labels

GBP 164.30

1

Advanced MXP-642 Commander BACnet Modbus IP Interface StandardBasic

Advanced MXP-642 Commander BACnet Modbus IP Interface StandardBasicThe Advanced Commander is a powerful IP-based solution for customers requiring protocol translation between their Advanced Fire Control Equipment and a Building Management SystemBMS. The device can be used as a simple bridge between manufacturers components providing seamless integration and delivering guaranteed performance. The conversion protocols supported by the Advanced Commander are those generally found in use by the most common Building Management Systems on the market today and are currently BACNet or Modbus.The Advanced Commander supports up to 640 ObjectsTags of information which can be configured and passed between network components and delivered to the Building Managements Systems BMS using TCPIP technology. The Advanced Commander has powerful Windows- based software management suite built-in to provide engineers with the ability to write Cause Effect strategy check data logging calendar and timer functions. TCPIP connectivity permits the Advanced Commander to be located locally to the distributed network of Fire Control Panels but at the same time caters for remote programming and Building Management System BMS accessKey FeaturesBacNetModbus Protocol Integration640 Configurable ObjectTagsWindows-based ProgrammingPowerful IP ControllerConfigurable on a ZonePoint basis per Object for Fire Fault Alarm IsolationEngineer configurable over TCPIPSupports a single Ad-Net networkSmall CompactLow Voltage 12vDC - 24vDCPlease Note This unit requires MXP-510 BMS Interface.

GBP 2059.25

1

Brand

Merchant

Price (EUR)